Water spraying out of a wall or raining through a light fixture is not a wait-until-morning problem. Shut the main, then call Water Heater Repairer and a live dispatcher will route you to an independent, licensed and insured plumber near you, plus a water damage contractor if the mess calls for one.
A burst pipe is two jobs at once: stopping the leak and dealing with the water it already dumped. We line up both trades so you are not making five calls while water keeps moving.
Pipe work inside walls touches code, so calls are routed to licensed and insured independent plumbers. Feel free to ask for their license at the door and verify it yourself.
A spraying line inside a finished wall gets priority over a slow drip under a sink. Response is typically fast, though a hard freeze can stretch every schedule in town.
The plumber explains what has to open up and writes a flat-rate price before cutting drywall. You know the number before the first tool comes out.
Plenty of the plumbers we route to bring acoustic listening gear and a thermal camera. That means smaller access holes and less guessing about where the split actually is.
Freeze breaks, corroded galvanized runs, cracked CPVC fittings, and slab leaks all come through this line. Tell the dispatcher what the pipe looks like and where it runs, and we match you with someone who works on that material every week.
When water has already soaked drywall, insulation, or subfloor, fixing the pipe is only half the job. A drying contractor with moisture meters, air movers, and dehumidifiers can be sent so the cavity dries out before the wall is patched. Sealing up a damp cavity is the fastest way to end up with a mold problem by spring.
Pipe material, location, and the reason it broke decide which repair makes sense.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. The ice pushes pressure toward a closed fixture until the pipe splits, and the leak usually shows up once it thaws.
Type M copper has a thinner wall than Type L, so it tends to split and pinhole sooner. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX rarely splits, but crimp and expansion fittings can blow off when water freezes inside them. Aging CPVC gets glass-brittle, so a cracked elbow often means nearby joints are close to failing too.
A hot spot on the floor or a meter that spins with every tap closed points to a slab leak. Acoustic detection and thermal imaging pin it down, then you weigh a spot repair against a reroute through walls or attic.
Old galvanized pipe corrodes from inside out, and the threads are usually where it gives up. Patching one section of a rotted run often just moves the leak a few feet down the line.
Braided supply lines under sinks and toilets burst without warning, and they run at full house pressure. A water heater relief valve that keeps discharging is a separate warning sign worth a call.
The process is short, and a real person handles each part.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask about the pipe material, the location, and whether any ceiling is sagging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water reached floors or walls, a drying contractor can be lined up on the same call.
The pro locates the split, looks over the rest of the line, and notes any pinholes or brittle fittings nearby. A written, flat-rate quote comes before any drywall is cut.
The permanent repair goes in, the line is pressure tested, and the plumber watches the joint under full pressure before closing anything up. Ask about the contractor's own written workmanship warranty before they leave.
A push-to-connect coupling can stop a spraying line in minutes, which makes it a solid emergency patch. Many plumbers still prefer a sweated or press fitting behind drywall, since that joint will sit unseen for decades.
Close the main valve, then call and we will route a local licensed plumber to you.
A pipe in the outside wall of our laundry room froze and split during the first cold snap. I found the main because the dispatcher stayed on the phone with me, and the plumber had the split copper cut out and replaced within a couple hours. He also showed me the Type M pipe and explained why it went first.
The bill jumped and part of the hall floor was warm to bare feet. They found the hot line leaking under the slab with an acoustic detector and a heat camera. He gave us a written price for a spot repair and another for rerouting through the attic, and let us pick.
Water came through the dining room ceiling from an upstairs bathroom supply line. The plumber fixed the line and a water damage contractor showed up after to dry the ceiling and floor. Having both lined up from one call saved me a long night of searching.
I manage a small rental, and a tenant called about a CPVC elbow that cracked under the kitchen sink. After the repair he showed me how brittle the other joints were, and two of them snapped in his hand. He quoted a full repipe of that wall in writing and did not pressure me to do it that day.
Shut off the main water valve, then switch off breakers for any circuits near the water. Open a lower faucet to drain the lines, move valuables, and call so a plumber can head your way.
Turn on the connected faucet and apply gentle heat with a hair dryer or a space heater nearby. Never use a torch or open flame, since it can scorch framing or flash steam inside the pipe.
Many are rated for permanent use, but plenty of plumbers treat them as temporary inside a closed wall. Have the plumber explain whether a sweated or press joint is the better long-term choice.
Listening equipment hears the leak, and a thermal camera maps the wet area through the drywall. That combination typically keeps the cut small and easy to patch later.
A single leak on newer pipe often makes sense to spot repair through the floor. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Drip faucets on exterior walls during deep cold and leave cabinet doors open for heat. Heat tape and foam insulation on crawlspace and attic runs help a lot, and the plumber can point out the worst spots.
Calls go to independent plumbers covering Kyle, from older homes with galvanized pipe to new construction running PEX. Surrounding suburbs are part of the coverage, including zip codes like 78666 78640.
Older homes near the center of town tend to have galvanized mains and thin copper branch lines, which is where pinhole leaks and corroded threads show up. Newer subdivisions lean on PEX and CPVC, where freeze-popped fittings and brittle elbows are the usual story. Give the dispatcher a rough age for the house and we route someone who knows that era of plumbing.
Crawlspace freezes, attic lines, and slab leaks in houses of every age.
Shared-wall leaks where stopping the water fast and documenting it for the association both count.
Surrounding towns around Kyle are covered by the same network.
